SOK Battery 100Ah 12V LiFePO4 Lithium Iron Phosphate Deep Cycle Battery,Perfect for Your RV or Any Off-Grid Applications,Low Temperature Disconnected.

Product Information

The lowest safe storage temperature is -22°F, so any temperatures below this, you should bring them inside or add a heating pad of some sort, but keep in mind if a heating pad runs out of power and the battery falls below -22°F, damage may occur. SOK models have a temperature performance of (-22~140°F) for discharges and (32~140°F) for charges and a BMS Low/High-temperature cut-off of 32°F/149°F respectively. On the other hand, Lion batteries have an operating temperature range of (32~113°F) for charges and a range of (-4~131°F) for discharges. Yes, however you will need to manually set the appropriate settings within the inverter manually, and run these batteries in an open-loop, voltage control based configuration. When compared to AC wiring, Low-voltage DC systems are very susceptible to voltage drop. Long cable runs between batteries and inverters can lead to premature low-voltage shutdown when heavy loads are turned on. For optimal performance, keep your batteries as close to your inverter/charge controllers as possible. Temperature

Using the up and down arrows, navigate to the battery type setting (#14 LVX 6048) (#5 LV 6548). Press the “⏎” key to change the setting. Using the up and down arrows, adjust the setting parameter until “PYL” is shown. Press the “⏎” key one more to save the setting. Ensure all batteries are in the “BMS-OFF” state prior to installing the cable(s) as explained in the shutdown procedure. We recommend keeping any AC and PV inputs to the Voltronic inverter OFF during this procedure.

We thank you for the continued use of Current Connected, LLC. as your resource, and we hope this Training Manual will better assist you in understanding your project and enable you to meet your goals. Printing Ensure all batteries are in the “BMS-OFF” state prior to installing the cable(s) as explained in the shutdown procedure. After the cable(s) have been installed, power up the system per the proper pre-charge procedure. If the battery is not detected by the Cerbo: Note: if the batteries have been fully charged, you would expect the menu in step 4 to eventually show 0A for charge current, but the full 475A for discharging current. This is to be expected. Warning triangle on home screen: As for most electronics, extreme humidity & condensation is not good for long term performance or integrity. Avoid environments that have condensing humidity and be especially cautious in locations near the ocean where salt spray may be present, as this can cause accelerated degradation that wouldn’t be covered by warranty. If a high humidity application is expected, install the batteries in a sealed / outdoor rated enclosure. Proximity to Equipment Battery Starts Synchronized: Disabled (NOTE: you will need to fully charge your battery to sync up SOC%)

High inrush currents can be prevented using a pre-charge resistor. The pre-charge resistor allows the capacitors in the controller to slowly charge BEFORE the low-resistance circuit is in place. This means that the powering-up of inverters and chargers is regulated and graceful, rather than abrupt and volatile. A pre-charge resistor can be built into an automatic circuit or used manually. Built In Automatic Pre-Charge Circuit Product not stored in adherence to the Manufacturer’s storage guidelines, including storage of the Product at low state-of-charge. Experience reliable and long-lasting power with the SOK 12V 100Ah Lithium-Iron Phosphate (LiFePO4) Deep Cycle Battery. It’s designed to exceed expectations and deliver unparalleled performance for all your power needs. Whether you’re embracing the freedom of van life, enjoying the comforts of an RV, or powering your off-grid cabin, this battery is your dependable energy companion. Don’t settle for less when you can have exceptional value with an SOK Battery! Capacity and Voltage Low Temperature Protection. Every other battery at this price point does not have low temperature cut off. This one does!Now, you may turn on the DC breakers and BMSs in the rest of the batteries as described previously. You may now use your system. Success! You can now select the Dashboard, Charts, Totals, or Power menu tab to view real-time updates from your SOK 48v100Ah battery. Flash the SD card, as described in the SolarAssistant documentation here: https://solar-assistant.io/help/getting-started/prepare-device This is their only large form factor 12V battery that has high charge and discharge rating, but also has low temp protection. Choose the SOK 12V 100Ah Lithium-Iron Phosphate Deep Cycle Battery for reliable power, exceptional durability, and a range of intelligent features. Whether it’s for your RV, van life, off-grid cabin, or other applications, trust the SOK battery to deliver outstanding performance and value!

Low Temperature Cutoff: Disabled (unless you add a temp sensor, the BMS has this protection built in) Settings for Renogy Charge Controller (Wanderer, etc.) If you can, we recommend setting the equalization voltage to 14.6v. With this set at 14.6, if an equalization is somehow triggered, you will not damage your battery. Victron Settings For SmartShunt & BMV-712 / SOK BatteryMicroUSB adapter to provide power to the Pi. Alternatively you can use a 5v power supply. Refer to your Pi documentation for power requirements I have tested a lot of batteries, and this one blows away the competition. If you want a budget battery that will not give you any problems, this is the way to go! With a maximum discharge of 100A and maximum charge rate of 50A, this battery is capable of delivering and receiving power efficiently, catering to your power demands. Detachable Cover and Replaceable BMS and Cells This manual is not a substitution for proper training. The intended use of this manual is to provide guidance and reference for the use of products sold by and associated with Current Connected, LLC. All materials mentioned in this Training Manual range in technicality and require varying competency levels and expertise. Therefore it is recommended to seek proper training before using products seen and mentioned in the training manual.